Dry Ice Blasting Mold in Panorama City, California

Chemical-free mold removal for framing, attics and crawl spaces

Dry Ice Blasting Mold in Panorama City, California lifts mold off wood framing, joists and sheathing using compressed CO2 pellets instead of water, sand or harsh chemicals. If you have spotted black mold behind drywall, smelled that musty odor in a North Hills rental, or found attic mold after a roof leak, our IICRC-trained technicians can blast the growth away and leave the surface dry and ready for encapsulation.

A powerful image of molten metal pouring in a heavy industry steel mill setting.

What Dry Ice Blasting Mold in Panorama City, California Does

Dry Ice Blasting Mold in Panorama City, California is a non-abrasive remediation method that fires rice-sized CO2 pellets at roughly -109°F through a pressurized blasting machine. The pellets hit the mold, flash-freeze it, and the sudden temperature change pops the growth off the surface. Because the dry ice sublimates on contact, there is no water, no sand, and no chemical residue left behind. We use it on wood framing, roof sheathing, floor joists, concrete block and even electrical panels where wet methods would be a bad idea.

Panorama City homes sit in a hot, dry San Fernando Valley climate, but that does not stop mold. A single pipe burst under a Kester Avenue sink or a slow roof leak near Van Nuys can soak framing for weeks before anyone notices. We see crawl space mold after winter rain, bathroom mold from poor ventilation, and attic mold from roof leaks across the 91402 ZIP code. If you have been searching for dry ice blasting mold in Panorama City California near me, our crew handles both residential and commercial jobs, including CO2 blasting mold remediation for commercial building Panorama City California properties.

Why Choose Dry Ice Blasting for Mold Removal

Why Choose Dry Ice Blasting for Mold Removal

Dry ice blasting removes mold faster and cleaner than sanding, wire brushing or chemical washing, and it lets us treat framing, wiring and ductwork in a single visit without adding moisture to a building that is already fighting it.

No Water, No Secondary Damage

Wet media blasting and pressure washing push moisture into wood and drywall, which is exactly what mold needs to come back. Dry ice sublimates into CO2 gas on contact, so the surface stays dry. On a typical 400-square-foot attic, we finish in about three hours and the framing is ready for encapsulant coating the same day.

Reaches Tight Framing Cavities

We slide a boroscope inspection camera behind drywall and into wall cavities, then blast the mold we find on studs, sill plates and sheathing without tearing the whole wall apart. That saves hundreds of dollars in drywall replacement and keeps your kitchen or bedroom livable during the job.

Safe Around Wiring and Ducts

Because there is no water and no abrasive grit, dry ice cleaning mold Panorama City California crews can treat around electrical wiring, junction boxes and HVAC ductwork. We still de-energize circuits when needed, but you avoid the corrosion risk that comes with liquid-based mold cleanup.

Kills the Musty Odor at the Source

Mold spores trapped in wood grain and insulation keep producing that musty smell even after you wipe surfaces down. Blasting removes the colony and its food source, then we follow with a HEPA vacuum and antimicrobial solution. Most customers tell us the odor is gone within 24 hours of the final walkthrough.

Our Dry Ice Blasting Mold Process

Every job follows the same five steps, from the first moisture reading to the post-remediation spore test. Most residential jobs finish in one to two days, and we walk you through each stage before we start.

1

Inspection and Testing

We start with a moisture meter and thermal imaging camera to map where water has traveled, then take air samples with a Zefon Air-O-Cell spore trap cassette. You get a written scope the same day, usually within two hours of arrival.

2

Containment Setup

We seal the work zone with 6-mil containment plastic sheeting and zipper doors, then run a negative air machine with HEPA filtration and an air scrubber. This keeps spores from spreading into the rest of your Panorama City home while we work.

3

Dry Ice Blasting

Our technician feeds CO2 pellets through a dry ice blasting machine and works the affected framing, sheathing and joists in overlapping passes. A typical attic takes two to four hours. The mold freezes, pops off, and the pellets disappear as gas.

4

HEPA Vacuum and Treatment

We vacuum every blasted surface with a HEPA vacuum, then apply an antimicrobial solution and, where the wood will stay exposed, an encapsulant coating. A fogging machine treats the air space and any ductwork we could not reach directly.

5

Clearance Testing

Two to three days after we finish, we run post-remediation mold testing with a fresh spore trap cassette and compare the indoor count to an outdoor baseline. You get the lab report by email, usually within 48 hours.

Five Years of Valley Mold Experience

Mold Remediation Service Panorama City has been blasting mold out of San Fernando Valley buildings since 2021. In that time we have handled hundreds of jobs across Panorama City, North Hills, Van Nuys and Sepulveda, from single bathroom ceilings to full commercial warehouses. Our technicians hold IICRC WRT and AMRT certifications, and we follow California Department of Public Health guidelines on every project. We are EPA Lead-Safe Certified, OSHA 10 trained, and hold an active California CSLB license, so the work is done to code from the first containment staple to the final clearance test.

  • IICRC WRT and AMRT certified technicians on every dry ice blasting mold job
  • EPA Lead-Safe Certified and OSHA 10 trained crews
  • Active California CSLB license and full insurance coverage
  • Hundreds of completed jobs across the 91402 ZIP code and surrounding Valley neighborhoods
  • Post-remediation clearance testing included on every project
Five Years of Valley Mold Experience

Why Panorama City Homeowners Pick Our Dry Ice Blasting Mold Crew

We are a local crew, not a franchise call center. When you call, you reach a technician who knows Panorama City building stock, from 1950s tract homes near Roscoe to newer commercial builds along Van Nuys Boulevard.

Same-Day Response Available

We offer same day dry ice blasting mold Panorama City appointments for active leaks and emergency calls. Call before noon and we can usually have a technician at your door within four hours, with containment set up the same visit.

Upfront Flat-Rate Pricing

You get a written price before we start, and it does not change unless you add scope. Affordable dry ice blasting mold Panorama City 91402 jobs start around $650 for a single bathroom and scale with square footage, not with how long we happen to be on site.

Dry Ice Mold Remediation in Panorama City Without Chemicals

We use CO2 pellets, HEPA filtration and EPA-registered antimicrobials, not bleach or foggers that leave residue. That matters if you have kids, pets or anyone with asthma. The dry ice mold remediation Panorama City process leaves no chemical smell and no wet surfaces behind.

Clearance Testing Built In

Every job ends with post-remediation mold testing using a Zefon spore trap cassette and an outdoor baseline. You get a lab report showing the indoor spore count dropped to normal levels, which is what your insurance adjuster and any future buyer will want to see.

What Our Dry Ice Blasting Mold Service Includes

Every dry ice blasting mold job includes inspection, containment, blasting, HEPA vacuuming, antimicrobial treatment and clearance testing. Add-ons like drywall replacement, insulation removal and duct cleaning are quoted separately after the inspection so you can see exactly what is included before you approve the work.

What's Included

Moisture Mapping and Inspection

We use a moisture meter and thermal imaging camera to find every wet area, then a boroscope inspection camera to check inside wall cavities. This tells us exactly which framing needs blasting and which does not.

Containment and Negative Air

We seal the work zone with 6-mil containment plastic sheeting and zipper doors, then run a negative air machine and an air scrubber with HEPA filters. Spores stay inside the containment for the whole job.

CO2 Blasting of Affected Surfaces

Our technician blasts the mold off wood framing, joists, sheathing and concrete using a dry ice blasting machine. A typical attic takes two to four hours; a bathroom wall cavity takes about 90 minutes.

HEPA Vacuum and Antimicrobial Treatment

After blasting, we vacuum every surface with a HEPA vacuum and apply an antimicrobial solution. Exposed framing that will stay visible gets an encapsulant coating to seal the wood.

Post-Remediation Clearance Testing

We collect air samples with a Zefon Air-O-Cell spore trap cassette and compare them to an outdoor baseline. You get the lab report by email, usually within 48 hours of sampling.

Mold Problems We Solve With Dry Ice Blasting

Most Panorama City mold calls fall into a handful of categories: leaks behind walls, attic growth from roof damage, crawl space mold after rain, and HVAC contamination. Dry ice blasting handles all of them without adding water to the structure.

Problem

Black mold behind drywall after a slow leak

Left alone, the colony spreads along the studs and into adjacent rooms, and the musty odor gets into furniture and clothing.

Solution

We cut a small inspection port, confirm the species, and blast the mold off the studs and sill plate. In most cases the drywall can be patched rather than replaced, which saves several hundred dollars.

Problem

Attic mold from a roof leak near Van Nuys

Attic mold spreads fast in the Valley heat and can drip condensation onto ceiling drywall below, turning a small repair into a full ceiling replacement.

Solution

We contain the attic, blast the sheathing and rafters, then treat with antimicrobial and encapsulant. Most attic jobs finish in one day and pass clearance testing on the first try.

Problem

Crawl space mold after winter rain

Crawl space mold feeds the musty smell that rises into the living space and can rot floor joists over time, leading to sagging floors.

Solution

We blast mold off the joists and subfloor, install a vapor barrier where needed, and treat the space. Dry ice cleaning mold from crawl space Panorama City California areas avoids the moisture problem wet methods create.

Problem

HVAC mold contamination spreading through the house

A contaminated air handler pushes spores into every room each time the system runs, which is why the smell keeps coming back no matter how much you clean.

Solution

We blast the accessible duct interiors and air handler cabinet, then run a fogging machine with antimicrobial through the system. Clearance testing confirms the spore count dropped.

When to Call for Dry Ice Blasting Mold

1

You found black mold on the framing behind a bathroom wall in a 1950s Panorama City home.

Solution:

We open a small inspection port, blast the mold off the studs and sill plate, then treat the cavity with antimicrobial solution. No need to tear out the whole wall.

Outcome:

Framing is clean, the wall is patched, and clearance testing confirms the air is back to normal within a week.

2

A roof leak soaked your attic sheathing and you can see dark staining across the rafters.

Solution:

We contain the attic, blast the sheathing and rafters with CO2 pellets, then apply encapsulant coating to the exposed wood.

Outcome:

Attic is mold-free and sealed, and the roof repair can proceed on a clean surface.

3

Your commercial building on Van Nuys Boulevard has mold in a storage room after a sprinkler line failed.

Solution:

We schedule CO2 blasting mold remediation for commercial building Panorama City California projects after hours, contain the room, blast the joists and walls, and run clearance testing before reopening.

Outcome:

You lose zero business days and get a lab report for your insurance file.

4

You smell musty odor in the living room but cannot see any mold.

Solution:

We inspect with a thermal imaging camera and boroscope to find the hidden moisture source, then blast whatever framing is affected.

Outcome:

The odor source is removed, not masked, and you get documentation showing the indoor spore count dropped.

Tools and Methods We Use

Tools & Equipment

Dry Ice Blasting Machine

Fires rice-sized CO2 pellets at roughly -109°F to flash-freeze and lift mold off wood, concrete and metal without abrasion.

Thermal Imaging Camera

Reveals temperature differences that point to hidden moisture behind drywall, under flooring and inside ceiling cavities.

Boroscope Inspection Camera

Slides through a small drilled hole to show us what is happening inside a wall cavity before we commit to opening it up.

Air Scrubber with HEPA Filter

Filters airborne spores and debris inside the containment zone, keeping the rest of the home clean during blasting.

Negative Air Machine

Maintains negative pressure inside containment so air flows in, not out, and spores cannot escape into adjacent rooms.

Zefon Air-O-Cell Spore Trap Cassette

Collects airborne spores for lab analysis. We use it for the pre-job baseline and the post-remediation clearance test.

Fogging Machine

Applies EPA-registered antimicrobial solution to ductwork and air spaces that blasting cannot reach directly.

Methods

IICRC S520 Mold Remediation Standard

We follow the IICRC S520 standard for containment, removal and clearance on every job. That means documented moisture readings, sealed containment, HEPA filtration and post-remediation verification before we call a job complete.

California Department of Public Health Guidelines

Our inspection and clearance protocols follow California Department of Public Health guidelines for mold assessment. That includes outdoor baseline sampling, which is the only way to interpret an indoor spore count accurately.

Containment and Negative Pressure

We build 6-mil containment with zipper doors and run negative air throughout the job. This keeps spores from spreading into unaffected rooms while we blast the affected framing.

Encapsulant Coating

After blasting and antimicrobial treatment, exposed framing gets an encapsulant coating that seals the wood surface. This is especially important on attic sheathing and crawl space joists that stay visible.

How Dry Ice Blasting Mold Works in Panorama City

Panorama City sits in the San Fernando Valley, where summer heat pushes attic temperatures past 140°F and winter rain finds every weak point in a roof. That combination creates two very different mold patterns. In summer, HVAC systems run hard and any moisture in the air handler turns into mold fast. In winter, roof leaks and crawl space dampness drive the calls. Most of the housing stock here dates from the 1950s and 1960s, which means original wood framing, older plumbing and plenty of wall cavities that have never been opened. Dry ice blasting mold in Panorama City, California is a good fit for that housing stock because it cleans framing in place instead of requiring full tear-out. If you have been looking for dry ice blasting mold in Panorama City California near me, we cover every neighborhood from Panorama City Center to Wolfe and Osborne, and we can usually schedule an inspection within 24 hours.

Service Areas

Panorama City Center

Older commercial and residential mix with frequent HVAC mold calls from restaurants and small offices along Van Nuys Boulevard.

North Hills

Single-family homes with original 1950s plumbing. Slow leaks behind bathroom walls are the most common mold source we see here.

Van Nuys

A mix of apartments and single-family homes. Attic mold from roof leaks is the top call in this area during winter.

Sepulveda

Crawl space mold after rain is common in the older homes near Sepulveda Boulevard, especially where vapor barriers are missing.

Roscoe

Residential streets with mature trees that drop debris on roofs, leading to slow leaks and attic mold over time.

Local Considerations

Summer attic temperatures above 140°F

Heat drives moisture into the attic from below and accelerates mold growth on sheathing. We schedule attic blasting in the early morning to keep the work safe and efficient.

Winter rain and roof leaks

Even a small roof leak can soak sheathing for weeks before it shows on the ceiling. We inspect with a thermal imaging camera to catch it early.

1950s plumbing with slow leaks

Original galvanized and copper lines fail slowly, soaking wall cavities. Dry ice blasting lets us clean the framing without tearing out the whole wall.

Crawl spaces without vapor barriers

Ground moisture rises into the subfloor and joists year-round. We install vapor barrier where needed and blast the affected wood clean.

Bathroom Wall Framing in Panorama City Center

Before

A slow supply line leak behind the shower had soaked the studs and sill plate for months. Black mold covered about 30 square feet of framing, and the musty smell had spread into the adjacent bedroom.

After

We contained the bathroom, blasted the mold off the studs and sill plate in about 90 minutes, treated with antimicrobial, and patched the wall. Clearance testing showed indoor spore counts at outdoor baseline levels.

Maintenance & Follow-up

Fix the supply line, run the exhaust fan for 20 minutes after every shower, and check under the sink once a month for moisture.

Before

A roof leak near a vent stack soaked the sheathing and two rafters. Dark mold staining covered roughly 60 square feet, and condensation was starting to drip onto the ceiling drywall below.

After

We blasted the sheathing and rafters in a single three-hour visit, applied encapsulant coating to the exposed wood, and the roof was repaired the following week. The clearance test passed on the first try.

Maintenance & Follow-up

Have the roof inspected every fall before the rainy season, and check the attic for staining after any major storm.

Before

Winter rain had pooled under the house for weeks. Floor joists and the subfloor showed mold growth across roughly 200 square feet, and the living room above smelled musty year-round.

After

We blasted the joists and subfloor, installed a vapor barrier across the crawl space floor, and treated the wood with antimicrobial. The musty odor cleared within 48 hours of the final walkthrough.

Maintenance & Follow-up

Keep the vapor barrier intact, check the crawl space after heavy rain, and make sure downspouts discharge away from the foundation.

Frequently Asked Questions

Have questions? We have answers.

Call Us
How much does dry ice blasting mold cost in Panorama City California?

Most residential jobs in Panorama City run $650 to $2,800 in 2026, depending on square footage and how far the mold has spread. A single bathroom ceiling sits near the low end; a full attic with roof sheathing and joists sits higher. Commercial spaces and crawl space jobs are quoted after inspection. We give you a flat written price before any work begins.

How does dry ice mold remediation work in Panorama City, California?

We feed rice-sized CO2 pellets through a blasting machine at roughly -109°F. The pellets hit the mold, flash-freeze it, and the temperature shock pops the growth off the wood or concrete. The dry ice turns straight into gas, so nothing is left behind but the mold debris, which we vacuum up with a HEPA vacuum and treat with antimicrobial solution.

Is dry ice blasting safe for electrical wiring in Panorama City?

Yes. Dry ice blasting uses no water and no abrasive grit, so it will not corrode wiring or push moisture into junction boxes the way pressure washing can. We still de-energize circuits in the work zone as a precaution, and we keep the blasting nozzle at a safe distance from exposed conductors. Most electrical panels and conduit runs can be cleaned in place.

Does dry ice blasting kill mold or just remove it in Panorama City California?

It removes the mold colony, its spores and the surface layer of wood it was feeding on. That is more than most chemical treatments do, because bleach and foggers often leave the root structure behind. We follow every blast with an antimicrobial solution and, on exposed framing, an encapsulant coating. Clearance testing then confirms the spore count dropped to normal.

Licensed, Certified and Locally Accountable

Certifications

IICRC WRT (Water Restoration Technician) by Institute of Inspection, Cleaning and Restoration Certification
IICRC AMRT (Applied Microbial Remediation Technician) by Institute of Inspection, Cleaning and Restoration Certification
EPA Lead-Safe Certified Firm by U.S. Environmental Protection Agency
OSHA 10 Construction Safety by Occupational Safety and Health Administration
California CSLB Licensed Contractor by California Contractors State License Board

Reviews

Google

They blasted mold off the framing behind our bathroom wall instead of tearing everything out. Containment was tight, the crew was clean, and the clearance test came back clean on the first try. Saved us about $1,200 compared to the other quote we got.

Yelp

Called about attic mold after a roof leak in North Hills. They were out the next morning, had containment up by 9am, and finished blasting by early afternoon. Lab report came back two days later. Straightforward pricing, no surprises.

BBB

We manage a small commercial building near Van Nuys Boulevard and had mold in a storage room. They scheduled after hours so we did not lose a day of business. Professional crew, clear communication, and the post-remediation test passed.

Google

Musty smell in the living room for months and no visible mold. They found the source in the crawl space with a thermal camera, blasted the joists, and installed a vapor barrier. Smell was gone within two days. Worth every penny.

Related Services

Mold Inspection Near Me

Before any dry ice blasting mold work starts, we inspect the affected area with a moisture meter and thermal imaging camera. This tells us how far the mold has spread and whether hidden cavities need blasting too.

Mold Inspection Near Me

Mold Inspection

A full inspection maps the moisture source and the mold footprint. We use this to build the blasting scope, so you are not paying to treat framing that is already dry and clean.

Mold Inspection

Mold Testing

Lab testing confirms what species of mold is present and how high the spore count is. We run these tests before blasting and again afterward to prove the dry ice mold remediation Panorama City work actually cleared the air.

Mold Testing

Mold Testing Near Me

Same-week mold testing for Panorama City homeowners who need documentation for insurance, a real estate sale or a landlord dispute. Results come back from the lab in about 48 hours.

Mold Testing Near Me

Certified Mold Inspector

Our certified mold inspector documents conditions room by room, including photos and moisture readings. That report becomes the baseline for the dry ice blasting mold scope and the clearance test.

Certified Mold Inspector

Black Mold Inspection

Black mold behind drywall is one of the most common calls we get. We open a small inspection port, confirm the species, and blast the affected framing without tearing out the whole wall.

Black Mold Inspection

Home Mold Inspection

A top-to-bottom home inspection covers attic, crawl space, bathrooms and HVAC. It is the fastest way to find every mold problem before scheduling dry ice blasting mold in Panorama City California.

Home Mold Inspection

Residential Mold Testing

Residential testing covers single-family homes, condos and duplexes. We sample air and surfaces, then use the results to size the dry ice blasting job accurately.

Residential Mold Testing

Commercial Mold Inspection

Commercial inspections cover warehouses, retail and office space. We schedule after-hours so CO2 blasting mold remediation for commercial building Panorama City California projects do not disrupt your business.

Commercial Mold Inspection

Mold Remediation Company

As a full-service mold remediation company, we handle containment, blasting, HEPA vacuuming, antimicrobial treatment and clearance testing under one scope, so you are not coordinating three different contractors.

Mold Remediation Company

Emergency Mold Testing Services

When a pipe bursts or a roof leak soaks framing overnight, emergency testing gets you answers fast. We can usually be on site within four hours and start blasting the same day.

Emergency Mold Testing Services

Same Day Mold Testing

Same-day testing is available for active leaks and post-flood situations. Getting the samples collected quickly means we can schedule dry ice blasting before the mold spreads further.

Same Day Mold Testing

Basement Mold Inspection

Basements and below-grade rooms trap moisture. We inspect with a boroscope inspection camera, then blast mold off concrete block and framing without adding more water to the space.

Basement Mold Inspection

Attic Mold Testing And Removal

Attic mold from roof leaks is one of our most common dry ice blasting jobs. The dry process is ideal up there because it does not add moisture to insulation or sheathing.

Attic Mold Testing And Removal

Air Quality And Mold Testing

Air quality testing measures spore counts indoors against an outdoor baseline. It is the same test we use for clearance after dry ice blasting mold in Panorama City, California.

Air Quality And Mold Testing

Mold Remediation Near Me

If you are searching for mold remediation near me, we cover all of Panorama City and the surrounding Valley neighborhoods. Most jobs are scheduled within 24 to 48 hours of your first call.

Mold Remediation Near Me

Crawl Space Mold Removal

Crawl space mold after winter rain is common in older Panorama City homes. Dry ice cleaning mold from crawl space Panorama City California areas avoids the moisture problem that wet methods create in a confined space.

Crawl Space Mold Removal

Bathroom Mold Removal Service

Bathroom mold from poor ventilation often spreads into wall cavities. We blast the visible growth and any framing behind the tile or drywall, then treat the area to stop it returning.

Bathroom Mold Removal Service

Toxic Mold Removal

Toxic black mold needs containment and HEPA filtration before anyone touches it. We set up negative air, blast the colony off the framing, and run clearance testing before we remove containment.

Toxic Mold Removal

Mold Abatement

Mold abatement is the full removal and disposal process, including contaminated drywall and insulation. Dry ice blasting fits into abatement as the cleaning step for framing that stays in place.

Mold Abatement

Professional Mold Removal

Professional mold removal means IICRC-certified technicians, documented containment and clearance testing. Every dry ice blasting mold job we run follows that standard.

Professional Mold Removal

Mold Cleanup Near Me

Mold cleanup near me searches usually mean someone found visible growth today. We can inspect, contain and start blasting within a day or two of your call.

Mold Cleanup Near Me

Water Damage Mold Remediation

Water damage mold remediation starts with stopping the leak and drying the structure. Once framing is dry, dry ice blasting removes the mold without reintroducing moisture.

Water Damage Mold Remediation

Mold Spore Testing

Mold spore testing uses a Zefon Air-O-Cell cassette to capture airborne spores. We run it before blasting and again at clearance to confirm the air is back to normal.

Mold Spore Testing

Post Remediation Mold Testing

Post remediation mold testing is the final step after dry ice blasting. It gives you a lab report showing indoor spore counts dropped to outdoor baseline levels.

Post Remediation Mold Testing

Mold Fogging Treatment

Fogging treatment reaches ductwork and air spaces that blasting cannot. We use a fogging machine with an EPA-registered antimicrobial after the dry ice blasting step is complete.

Mold Fogging Treatment

Affordable Mold Remediation

Affordable mold remediation does not mean skipping containment or clearance testing. We keep costs down by blasting framing in place instead of tearing out drywall that can be saved.

Affordable Mold Remediation

24 Hour Mold Removal

24 hour mold removal is available for active leaks and emergency calls. We can set up containment overnight and schedule dry ice blasting first thing the next morning.

24 Hour Mold Removal

Odor Removal Mold

Musty odor removal starts with removing the mold colony, not masking the smell. Dry ice blasting strips the growth off framing, and the odor usually clears within a day of the final walkthrough.

Odor Removal Mold

Get Dry Ice Blasting Mold in Panorama City, California

If you have found mold behind drywall, in the attic or under the house, call Mold Remediation Service Panorama City at (833) 929-5837. We are IICRC-certified, licensed in California, and we include clearance testing on every dry ice blasting mold job. Most Panorama City calls get a same-week appointment.